Clik here to view.
Re: basic inter-vlan routing
Hi I think you will need to create ACL's and apply the ACL's to the subinterfaces
View ArticleRe: ibdump for Windows
Hello Aleksey, Can you please try to run it as 'ibdump -d mlx4_0 -i <port> -o <output file>' and let me know if it works?Also please run 'vstat' and 'ibstat' and share the output....
View ArticleRe: ibdump for Windows
Hello Einav, Thanks for advise. But I'm afraid it does not work.cmd was opened with admin privileges, output was like: c:\Program Files\Mellanox\MLNX_VPI\IB\Tools>ibdump.exe -d mlx4_0 -i 1 -o...
View ArticleConnect-X adapter fails to receive invalid IPv6 frame
Hello, I am using two Ethernet adapter cards (ConnectX-3 40G), on an Ubuntu system. I have noticed that certain Ethernet frames are not received by the cards, but are received fine by other Ethernet...
View ArticleConnect 2* HP switch with 2*Mellanox
Hi, I have 2 * Mallanox Switch SX1012 configured with MLAG. Is it possible connect 2 * ME SX1012 and 2 * HP 2910 Switch with RSTP like on the picture?Thanks--------------...
View ArticleRe: Connect 2* HP switch with 2*Mellanox
Can you explain what are you trying to do?Why don't you use MLAG configured on the SX1012 for example? Closing a loop between the switches will cause the RSTP to block one of the ports. se-rulez...
View ArticleClik here to view.
Re: Connect 2* HP switch with 2*Mellanox
We expect MLAG connectivity to be replicate what it would like if both the switches were one. So, we need the links in between the SX1012 and the HP switch. Once you have MLAG, RSTP is not required as...
View ArticleRe: ibdump for Windows
Hello Einav,As I've mentioned in first post My HW is Supermicro X9DRT-HIBQF based system with MCX353A-QCBT card. Card is burned with latest firmware.OS Windows 2012 Server is installed, WinOF 4.95 is...
View ArticleRe: Connect-X adapter fails to receive invalid IPv6 frame
Can you see that interface drops counters increase (ethtool -S)?
View ArticleRe: unable to create QP after set HUGE_RC to y
Could you try set these variables and run test againexport MLX_QP_ALLOC_TYPE=HUGEexport MLX_CP_ALLOC_TYPE=HUGE
View ArticleRe: unable to create QP after set HUGE_RC to y
Hi, Thank you for replying. I tried to set the above mentioned variables, but it still shows the same error messages.I guess you mean MLX_CQ_ALLOC_TYPE instead of MLX_CP_ALLOC_TYPE. I am running...
View ArticleRe: Connect-X adapter fails to receive invalid IPv6 frame
Thanks for your answer. Drop counters do not change, but the following counters increase by one when "not receiving" the problematic frame :rx_packetsvport_rx_filteredrx_novlan_packets Do you know what...
View ArticleRe: Connect-X adapter fails to receive invalid IPv6 frame
I found this link : Counters Troubleshooting for Linux Driver that describes the vport_rx_filtered counter as: Received packets dropped due to packet check that was failed. I would like to disable all...
View ArticleDisabling FEC On ConnectX-4 EDR
We have couple of ConnectX-4 EDR 100GbE NIC that we are using in Ethernet mode. Is there any way to disable FEC?
View ArticleSwitch boot problem
Hello, i have two SX6018 switches: one boots just fine, second one stops in a different mode: Switch-B(4)> and MLNX-OS commands are not available. Could anyone help me to figure out what is wrong?...
View ArticleRe: Disabling FEC On ConnectX-4 EDR
I don't know how to disable it, but I'm curious to know why you want to do this. Is it causing a noticeable performance drop? Thanks! --Anuj
View ArticleClik here to view.
Re: Disabling FEC On ConnectX-4 EDR
Yes, I know this. But, I need to do this to bring up link between the NIC and an 100G port on a switch.
View ArticleRe: Mellanox Drivers Needs Contract?
Is there a way to get the drivers for noncommercial purposes?
View ArticleRe: Disabling FEC On ConnectX-4 EDR
As far as i know, there is no way disabling FEC for 100G Eth
View ArticleRe: Switch boot problem
Hi Victor, From where did you buy the 2nd switch? From it's cli and fw version (9.9.xxxx), it seems that MLNX-OS is not installed and there is another customized OS installed on the switch.
View Article