Re: Partition configuration on Mellanox 5035 Fabric IT
you could run ibdiagnet from any IB node in the fabric. doesn't have to be from the switch itself..
View ArticleClik here to view.
Re: Partition configuration on Mellanox 5035 Fabric IT
This is ESXi host...:(How can I install OFED like Linux? Here is another test result. This link is another my experience about partition configuration on ESXi hosts. vSphere 5.1 U1 IPoIB VLAN support...
View ArticleRe: Partition configuration on Mellanox 5035 Fabric IT
I found MFT tools for ESXi host.I'll upload a result some time later...:)
View ArticleRe: Partition configuration on Mellanox 5035 Fabric IT
It seems ESXi tools can't support ibdiagnet on ESXi host...I'll try another system then I'll be back...
View ArticleClik here to view.
Re: Partition configuration on Mellanox 5035 Fabric IT
Here is a result via Intel vt-d direct through on Windows Server 2012 R2 with updateJust only default partition seen by ibdiagnet2...... Another result is hereIs there GUID problem on my HCAs?If so...
View ArticleClik here to view.
Re: Partition configuration on Mellanox 5035 Fabric IT
Hi!I found a problem on WebGUI. It should be add a Compute Node (port GUID), but partition-view sub menu shows only System GUID.I added Compute Node (port GUID) manually in CLI then all works properly....
View ArticleMellanox FDR14 active optical cable + Mellanox 5035 QDR switch = so many...
Is there anyone use Mellanox FDR14 active optical cable on QDR switch? I used this combination on old Voltaire 4036 QDR switch without any problems. I have a plan to migration to FDR fabric that cause...
View ArticleConnectX-2 Firmware / Performance?
Hi this is my first Post and my first venture in to the 10G World, I picked up 2 - ConnectX-2 Cards and installed them in two Hyper-V Servers to use as a private network connection for live migrations...
View ArticleRe: ConnectX-2 Firmware / Performance?
SMB Direct supported firmware 2.10.720 only.And if you have a ethernet adapter you must use DCB(X) 10Gb switch that can support loseless ethernet. Good luck...:)
View ArticleRe: ConnectX-2 Firmware / Performance?
Thanks for the reply, so I can't upgrade the firmware beyond the 2.9.1200 that I have now? This is where I am confused, why say I have an older / out of date firmware if a newer one isn't available /...
View ArticleClik here to view.
Re: ConnectX-2 Firmware / Performance?
Microsoft drive a RDMA support with SMB Direct - file based service, not block...:(I can't remember what VPI WinOF version contain firmware 2.10.720.You can get it archive driver link...:If you are...
View ArticleRe: qperf version in RHEL6
Hi Erez,The whole point is that we shouldn't have to use a Mellanox supplied RPM for a package which is already in the official Red Hat channels.The advice we got from our 3rd party supplier was to use...
View ArticleRe: it's normal speed?
Hi Sophie! I thinkit isthe speed limit. Speed PCI gen2 x8 = 32Gbits, do i understand correctly? ib_write_bw -d mlx4_0 -F 10.0.0.1...
View ArticleRe: Mellanox FDR14 active optical cable + Mellanox 5035 QDR switch = so many...
I'm complted test with varioty copper cables. All QSFP+ cables work propery.I can't find any symbol errors on 5035 switch during 3 hours load test and 12 hours real simulation test.It seems registered...
View ArticleClik here to view.
Re: How to enable extended tag on ConnectX-3 ?
ConnectX-3 adapters do not support extended tag. Extended tag is supported on ConnectX-4 / Lx and Connect-IB.
View ArticleClik here to view.
Re: ConnectX-2 Firmware / Performance?
Thanks again for the information but as I said this is my first venture in to the 10G World and while I certainly know what firmware is I don't have any clue on how to make my own firmware is there...
View ArticleClik here to view.
ibquery errrors and ipoib crash issue
hi I have an issue I've been struggling on with a new setup ive been working on. When keeping the network reasonably busy continuously IB interfaces are dropping out of the network. On the IB layer...
View ArticleRe: WHAT CABLE SHOULD I USE FOR Mallenox 40GB NIC COMMUNICATE WITH OTHER...
Yes, I do! I have several Mellanox cables. I'm also have Mellanox switch that have a capability embedded SM. At last I have 2 of Dell R310 1U servers for SM only system. These systemalmost in standby...
View ArticleRe: WHAT CABLE SHOULD I USE FOR Mallenox 40GB NIC COMMUNICATE WITH OTHER...
Hi Jae-hoon ChoiBut I am sorry , I don't know your current issue.If you have the same question is Jack? Thanks
View ArticleRe: ConnectX-2 Firmware / Performance?
Okay!I remember some link that resolve the same issue like you.Wait a some time.I'll find for you.The articles on the link will be helpful to you...:)
View Article