Re: Voltaire ISR-9024D (NOT -M) Question
http://community.mellanox.com/message/2010#2010 Sorry, wasnt trying to hijack, just seen you all had some good knowledge and prob subscribed to get email notices when a reply is made. So i thought i...
View ArticleRe: ISR9024D-M
I noticed in the directions for cabling it says this: To connect multi-purpose cable of an ISR 9024-M (internally managedunit):Step 1 Connect the DB-9 connector and the RJ45 connector to each extremity...
View ArticleRe: Voltaire ISR-9024D (NOT -M) Question
No worries. We're not super pedantic about it, it's just a good guideline to follow. Thanks for moving this to it's own thread.
View ArticleRe: Re: ISR9024D-M
Hmmm, the instructions with that "multi-purpose" cable sound fairly complicated. For my 9024D-M, I just plugged a standard everyday cat 5e ethernet cable into the front ethernet port (next to "I2C" DB9...
View ArticleRe: Re: ISR9024D-M
im going to have to try putting it on its own switch to eliminate complications. I tried the command above but it tells me: route_dst_netlink: can't find interface "vmbr0" This is on a proxmox lunix...
View ArticleRe: Re: ISR9024D-M
Wireshark shows me this everytime with the ISR directly connected to my second ether port on my desktop: 24250.097091000Heurikon_69:a1:a0BroadcastARP60Gratuitous ARP for 192.168.2.9...
View ArticleClik here to view.
Re: Re: Re: ISR9024D-M
Interesting, so it sounds like it's trying to use 192.168.2.9. "Heurikon" is most likely correct too, as that's how the board shows up in nmap as well: Re: Voltaire ISR-9024D (NOT -M) Question Are you...
View ArticleRe: UFM 4.0 server connection error - server not responding
That is correct! just set an IP address to your ib0 interface and that should do it!setting up the IP for the IB interface is the same as you would do for your Eth interface.
View ArticleRe: Re: Re: ISR9024D-M
I have put the ether on the same subnet as the switch (192.168.2.8) but i cannot ping the ISR. when i connect the ISR to a trendnet TEG-S80g 1GB switch it doesnt seem to establish a connection (both...
View ArticleRe: UFM 4.0 server connection error - server not responding
Hello. Yes, I have a license and I started ufmd with no errors. In /var/log/messages, I see the following: ufm: ufmd monitorufm: Running UFM in monitoring modeufm: Starting ibsim with options: -P...
View ArticleRe: UFM 4.0 server connection error - server not responding
Yes, part of my response was cut off, apparently because I had someunderline characters. Here is the rest of the log contents. Under ufm.log in /opt/ufm/files/log/, there is the following: UFM daemon...
View ArticleRe: Re: Re: ISR9024D-M
Interesting. It's obviously wanting to use the 192.168.2.9 address, but doesn't seem to be actually going ahead and using it. Unfortunately it's been ages since I had to work with IP(v4) network...
View ArticleRe: Re: ConnectX-3 not going up in Centos 6.4 (and SL6.4)
Just remembered... with flint you can query a card to extract the .ini file settings it already has: $ flint -d [PCI_bus_address_of_card] dc > somefile.ini For example, with an older card in a test...
View ArticleRe: VM Passthrough of MHQH19B-XTR
OK I tried flashing the 2.9.8350 firmware to no avail... I also tried disabling "VT-d" but then ESXi does not allow me to passthrough any device at all so I have to keep it enabled. Any suggestion?
View ArticleRe: dual-port HCA can ping if ib0 pair connected but not if only ib1 pair...
Hi justinclift,Thank you for your comment. I have tried the IP settings you posted. Things seem to work fine for the moment.I will check more as if those 2 links are really isolated.(when I run openmpi...
View ArticleClik here to view.
Re: dual-port HCA can ping if ib0 pair connected but not if only ib1 pair...
Hi Sorin,Yes, it is indeed a routing problem. I have tried the setting justin posted and things seem to work fine.Thank you!
View ArticleRe: error upgrading firmware
I just had a similar experience with the current fw version on flash displaying n/a and a DIFF DETECTED error. Used skip_is and so far so good. C:\mstflint_x64_2_7_2>mstflint -d mt25204_pci_cr0 -i...
View Article