Quantcast
Channel: Mellanox Interconnect Community: Message List
Browsing all 6211 articles
Browse latest View live

Image may be NSFW.
Clik here to view.

Re: SR-IOV CentOS 7 Host and CentOS 6.4 guest performance and right set up

Did you go thought Mellanox tuning guide? If system not tuned it can explain these variations in performance.

View Article


Re: OFED version support on mixed environment

Hi, to begin with, you will need to review the OFED release notes documents to determine whether you can use a certain version of OFED with a certain version of OS/Kernel.Mellanox Products: Mellanox...

View Article


How to configure vlan over bond for VMA?

My NIC is MCX312A-XCBT (Ethernet only dual port sfp+). CentOS 6.5.Mlx4_en driver + kernel tcp/ip + standart linux bonding/vlan are working just fine.I also have Mellanox ofed driver stack installed...

View Article

Image may be NSFW.
Clik here to view.

Replace the fiber optic cable

I have a problem to replace the fiber optic cable to an apparatus Mellanox Switch Sx6036. The cables that mounts now are: MC2207310-003-E-A2 I find that while most would be indicated: MC2207411-SR4 I...

View Article

Re: How to configure vlan over bond for VMA?

It turned out i missed routing config and bringing up all needed interfaces after ofed start

View Article


Image may be NSFW.
Clik here to view.

OpenSM service won't start

Hello, We have a couple of brand new systems - Intel S2600GZ with Windows 2008 R2 SP1 using the ConnectX2 card (MHQH19B-XTR). The issue we are having is that the OpenSM service stays in the 'Starting'...

View Article

Re: Link speed limited to 10gbps

Finally I got approved cable and firmware reported 40gbps link speed immediately. Nice job, Mellanox, on forcing us to buy special expensive cables. I would like to _emphasize_ that the QSFP+ that NIC...

View Article

Why LRO is disabled by default in mlx4_en driver?

Hello, run into this problem - why the mlx4_en driver does not enable LRO by default? Is there any reason for it? It takes some time to figure it out. Especially strange is that performance tuning...

View Article


Re: Issues with OFED 2.2.1 driver update

... was hoping someone in the community could provide some help ;-)

View Article


Re: Link speed limited to 10gbps

Hi Philip, Seems I met the same problem with you.Could you please tell me which kind of cable you finally use?And how about transceivers? Also Mellanox product? Thanks  for you help. Regards,Patrick

View Article

Re: Link speed limited to 10gbps

This is what I got. Mellanox has approved cables/QSFP+ list of their website, I just asked re-distributor to sell me "approved" cable.ORDER DETAILS                                    UNIT PRICE...

View Article

Re: Link speed limited to 10gbps

Forgot to mention that this cable has two transceivers fused at the ends,

View Article

Image may be NSFW.
Clik here to view.

Re: Link speed limited to 10gbps

PhilipMellanox does not lock its ports or require you to buy Mellanox cables. In fact, we constantly test third party cables in conjunction with our switches to ensure compatibility. The value...

View Article


Re: Link speed limited to 10gbps

Thanks Philip, Hope it can work also in our system. Regards,Patrick

View Article

Re: Link speed limited to 10gbps

Hi Anand, We met the similar issue with Philip's.CX314 card, two 40G ports connected back to back. We tested it both on Freebsd7.0 and CentOS 7.0.But the speed seen were always 10G.We didn't use...

View Article


Re: Link speed limited to 10gbps

Hello, Anand, Colfax International never communicated to me that you are expecting mstdump, I've plugged back generic cable/QSFP+, dumps are attached. Here is a link to generic MPO cable & QSFP+...

View Article

Re: Link speed limited to 10gbps

PatrickCould you please open a separate case with Support. We would like to triage it as if it were an independent issue.ThanksAnand

View Article


Image may be NSFW.
Clik here to view.

Re: Link speed limited to 10gbps

Philip,I had updated the ticket we created for this issue. Anyway, for now I have everything I need. Look out for an email from Mellanox Support Admin for further communication ThanksAnand

View Article

Image may be NSFW.
Clik here to view.

TEST CASE SALESFORCE

Asking a question

View Article

Re: Error /hca_self_test.ofed: line 165: [: too many arguments

All:Same exact symptoms here when running MLNX OFED 2.1-1.0.6 on RHEL 6.5 x86.  No errors during mlnxofedinstall at all, nothing indicating that all RPM's did not install. I am going to attempt...

View Article
Browsing all 6211 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>